97精品国产,午夜久久成人电影,午夜岛国视频,国产 欧美白虎一区二区三区

Online Service
Scan it
Support hotline
18681482740
Service Hotline:
18681482740
中文  |   English
News
Contact

Address: Floor 1, Building 2, Quanshengchang Industrial Park, Buyong Shajing Road, Shajing Street, Shenzhen

Contact: Mr. Li 18681482740

Email: lilinhan1314@126.com

Website: m.555198.cn

News
Analysis of Common Faults of Hardware Stamping Parts
03-15 / 2024

Hardware stamping is the first of the four main processes, and its importance can be imagined. The quality of the finished products from Shenzhen Hardware Stamping Factory will lay a solid foundation for the appearance and performance of the entire vehicle. Therefore, the quality assurance of stamping parts has always been a highly valued issue for automotive manufacturing enterprises. Based on the practical experience of quality management in stamping factories in China, the editor summarized common causes and countermeasures in the production process of metal stamping parts, hoping to provide some useful references for improving the quality of stamping parts.


Why does metal stamping parts exhibit steering distortion?


In progressive dies, metal stamping components form the shape of the punch by stamping the residual material around the stamping component. Stamping materials produce turning materials The main reason for distortion is the impact of impact pressure. During stamping, due to the presence of stamping gaps, the material is stretched (warped upwards) on one side of the mold and compressed on the punch side. When using the unloading plate, the material is squeezed by the unloading plate to prevent the material on the side of the mold from warping upwards. At this point, the stress state of the material changes accordingly. As the material increases through the discharge plate, the material on the punch side is stretched (the compressive force tends to decrease), and the material on the mold surface is compressed (the tensile force tends to decrease). The reversal of stamping is due to the stretching of the material on the mold surface. Therefore, when stamping, pressing and pressing the material is the key to preventing the punch from flipping. Reasons and countermeasures for bending and stamping during the bending process. 1. Caused by burrs generated by stamping. It is necessary to study the cutting-edge and pay attention to checking whether the punching gap is reasonable. During the punching process, stamping of stamping components was generated Distortion, resulting in poor forming after bending, needs to be addressed from the punching and unloading stations. Due to three bends, the stamped part is unstable. Mainly used for U-shaped and V-shaped bending. The handling of this issue is focused on bending the guide before impact during the bending process, which leads to material compression during the bending process to prevent the stamping components from sliding during the bending process.


Why can metal stamping components cause tearing? The stamping process for the middle panel bracket of metal stamping parts with common tearing and skewed shapes is: punching, punching, cutting, flanging, forming, cutting, and flanging. During the formation of the intermediate support, there are various forms of tearing and tilting. Due to stamping and production, the torn part is mainly distributed at the intersection of the hole shape, R-arc, and wall neck at the corner of the sidewall of the component. The differences in process conditions vary in the proportion of each fracture site. Tear can be a one-time tear, or it can be caused by fatigue cracks, i.e. the formation of invisible cracks. Based on the actual situation on site, the cause was analyzed and the tearing of the workpiece was determined to be, by examining the fracture shape and degree of fragmentation of the workpiece. Skew behavior is mainly reflected in the formation process of flipping. The reasons for this process are as follows:



1. The molding process parameters are not in place. In the process of forming parts, the mold, pressure core, and two parts must be tightly connected, and when the machine slider slides downwards, the plastic deformation of the paper is forced. Forming.


Hardware stamping parts | Hardware stamping terminals | Automotive hardware parts | Precision wire drawing parts | Motor chips | New


Links:Zibo CNC machine tool automatic car washing machine Qingdao refrigeration equipment grinder equipment steel grit fire inspection cabinet sweeper motor desulfurization denitrification equipment drawing mold washing machine automatic soldering machine server repair HART475 hand operator dust-free cloth dust-free paper stack screw type Sludge dehydration machine, precision repair welding machine, Shandong motor repair, rotary hot pot equipment, integrated ultrasonic cleaning machine, Zhongjie radial drilling machine, beer equipment, Shenzhen brass manufacturer, welcome lamp, lens digging, drilling rig, aluminum housing manufacturer, automatic dispensing machine, automatic screwing machine neodymium Iron boron magnet 4g router wireless bridge
We provide you with high quality products
欧美一区二区午夜| 久久在线观看理论视频| 国产亚洲天堂a v| 大香蕉视频影院在线亚洲国产_| 欧美久久久特级黄色片| 日本好好热视频在线| 乱伦 欧美 日韩 四区| 国产一级wwweewtic| 欧美,亚洲 自拍 偷拍| 草逼不卡免费视频| 日韩乱论网| 五月丁香网深爱婷婷| 麻豆传媒在线电影| 北条麻妃99精品青青久久| 国产台湾无码视频| 中文字慕AV一区二区| 国产情色综合网| 欧美熟妇WW欧美| 国产91在线|欧美| 甜蜜性色日韩AV| 国产精品美女精品1区2区3区 | 欧美日韩一区二区在线中文| 色狠狠久久一区麻豆| 久久亚洲精品国产亚洲老地址欧美| 自拍偷拍 熟女人妻 中文字幕| 台湾佬午夜成人福利| 日韩欧美成人wwww| 免费精品极品一级| av综合日韩中文| 欧美精品日韩无码欧美| 日本卡一卡二不卡视频| 精品一卡二卡三卡四卡兔在线| 中文有码_第1页_夜夜情| 国产区|97欧美精品资源在线| 国产富婆欧美流水在线| 国产在线不卡欧美精品| 成人 在线观看 国产 欧美精品| 午夜麻豆福利| 亚洲大胆人体视频| 国产精品久久久久久AV8m| 欧美持黄大片九九九|